Preview

Substation Equipment and Their Functions

Powerful Essays
Open Document
Open Document
57411 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
Substation Equipment and Their Functions
1. SUBSTATION EQUIPMENT AND THEIR FUNCTIONS
Substations INTRODUCTION: In Power System network, in order to transmit and distribute the generated power, it is necessary to install “SUBSTATIONS” at strategic points to work at required voltage level since “HIGH VOLTAGE TRANSMISSION” is resorted to. The Sub stations are classified as “GRID” of “RADIAL” Substations. The Grid station is installed in Grid network to reduce the voltage level from 230KV to 110 KV. The radial Station within Distribution net work to reduce the voltage from 110 KV to 11KV (or 22KV). In essence the substation provides (a) Transfer of voltage level (b) Transmission of the required Power and (c) Adjustment of voltage variations caused by the system voltage regulation. 110/11KV SUB STATION : CLASSIFICATION OF EQUIPMENTS

Sl. No
1.

Classification
Functional

Equipments
a) Bus Bar b) Transformers c) Earthing System

Purpose
To carry Power feeding To transmit Power from one voltage to other To ensure effective grounding for safety & Protective operation. Isolate feeding equipments from source of supply (Potential ) Breaking the Current (Power flow) for normal maintenance; and for isolation of faulty section) To prevent damage to equipment from direct stroke of lightning. Protecting the transformer from the impact of surges. Back up Protection for Surge Diverters. Metering (Voltage and Energy) Metering (Current & Energy) Protection For sensing the fault and give command to breakers to isolate the faulty circuit. For i) Indication of Status ii) Annunciation of the fault iii) Operation of breaker for isolation of faulty circuit. To feed L.T-3Ph. 400V Supply for i) Auxiliaries of breakers & Transformers. ii) Yard & Control room lighting iii) Supply to battery charge Control of A.C.Supply To house equipments with required horizontal and vertical clearances. To house indoor equipments like D.C.System, D.C. & A.C.panels etc.,

2.

Isolation & Control

a) Isolation

b) Breakers

3.

You May Also Find These Documents Helpful

  • Powerful Essays

    The protection system is one o the important aspect on which major manufacturers is concentrating. The companies like L&T, SIMENS etc. The protection system not only provides durability to the equipment but also avoid hazards. The protection system is one of the major fields in the electrical engineering. There are different types of protection systems out of that very common and important one is the voltage protection system. Normally all the electrical equipments are specified with a specific voltage range for its safe operation. When ever those equipments are applied with a voltage more then the upper specified limit the system may draw excess current which may cause to burn the equipment. The equipment is designed to withstand a specific voltage when ever the voltage goes beyond the limit value then automatically the insulations used in that equipment get punctured and cause a damage to the equipment. Similarly whenever the equipment is applied with a voltage lower then the lower specified voltage it draws excess current to maintain the efficiency. The out put may not be proper and the equipment may damage.…

    • 3006 Words
    • 13 Pages
    Powerful Essays
  • Satisfactory Essays

    Answers Copy

    • 369 Words
    • 2 Pages

    Comparison of voltages in each substation with the results got from Bewley Lattice Diagram and simulation results are shown in below,…

    • 369 Words
    • 2 Pages
    Satisfactory Essays
  • Powerful Essays

    The author of this assignment is a Senior Engineer at ZETDC Harare Region’s North District and the company is authorised to construct, operate and maintain the transmission and distribution system in various areas of Zimbabwe, and to offer the following distribution services:…

    • 2718 Words
    • 11 Pages
    Powerful Essays
  • Powerful Essays

    Different methods are used for locating. Lagrange method and two degrees gradiant and sensivity analysis method has been employed for placement [4]-[5]-[6]-[7]. This paper presents a new method for placement of DG units in distribution networks. This method is based on the analysis of power flow continuation and determination of voltage buses that are most sensitive to collapse voltage [8]. Subsequently, by selecting a objective function and using an iterative algorithm, DG units with known capacity will be installed on previously determined voltage buses. In iterative algorithm, the method of continuation power flow is used for determination of maximum loadability, thus it is needed to study the impact of different DG technologies on static voltage stability. This method will be executed on a typical 34-Bus test system. II-The impact of different DG technologies on Voltage Stability A. Synchronous Generator Conventional synchronous generators are capable of both generating and absorbing reactive power. Therefore, the use of DG’s utilizing overexcited synchronous generators will allow on-site production of reactive power. The local generation of…

    • 3723 Words
    • 15 Pages
    Powerful Essays
  • Good Essays

    Transformer

    • 1135 Words
    • 5 Pages

    Generation of Electrical Power in low voltage level is very much cost effective. Hence Electrical Power are generated in low voltage level. Theoretically, this low voltage leveled power can be transmitted to the receiving end. But if the voltage level of a power is increased, the electric current of the power is reduced which causes reduction in ohmic or I2R losses in the system, reduction in cross sectional area of the conductor i.e. reduction in capital cost of the system and it also improves the voltage regulation of the system. Because of these, low leveled power must be stepped up for efficient electrical power transmission. This is done by step up transformer at the sending side of the power system network. As this high voltage power may not be distributed to the consumers directly, this must be stepped down to the desired level at the receiving end with help of step down transformer. These are the use of electrical power transformer in the Electrical Power System.…

    • 1135 Words
    • 5 Pages
    Good Essays
  • Good Essays

    Iss Laws and Codes

    • 650 Words
    • 3 Pages

    NIST (national institute of standards and technology) – a federal agency within the US department of commerce, America’s first federal physical science research laboratory. NIST’s mission is to “promote US innovation and industrial competitiveness by advancing measurement science, standards, and technology in ways that enhance economic security and improve our quality of life.” NIST provides standards for measurement and technology on which nearly all computing devices rely. NIST maintains a list of standards and publications of general interest to the computer-security community. NIST executes its primary mission through four cooperative programs:…

    • 650 Words
    • 3 Pages
    Good Essays
  • Best Essays

    powerful computer based software. This research work highlights the effective use of Electrical Transient Analyzer Program…

    • 2373 Words
    • 10 Pages
    Best Essays
  • Good Essays

    enable it to interconnect with other electrical grids as well as operate in a parallel power…

    • 740 Words
    • 4 Pages
    Good Essays
  • Powerful Essays

    Earthing

    • 1086 Words
    • 5 Pages

    In the early power systems were mainly Neutral ungrounded due to the fact that the first ground fault did not require the tripping of the system. An unscheduled shutdown on the first ground fault was particularly undesirable for continuous process industries. These power systems required ground detection systems, but locating the fault often proved difficult. Although achieving the initial goal, the ungrounded system provided no control of transient over-voltages.…

    • 1086 Words
    • 5 Pages
    Powerful Essays
  • Powerful Essays

    Substation

    • 1394 Words
    • 6 Pages

    The SMS 510 substation monitoring system is an overall substation monitoring system that gives you essential information about your electrical transmission and distribution process. This information comprises all measured, recorded and calculated data such as indications, settings and diagnostic information available in the protection and control terminals from ABB. Setting and resetting facilities for the protection and control terminal are also provided by the product. The SMS 510 is a product for substation monitoring that allows the end users to configure the entire system themselves. SMS 510 is the ideal tool for creating tailor-made substation monitoring solutions that fulfil your specific requirements. From the very beginning this substation monitoring system was designed to take advantage of the Windows technology, thus providing an easy-to-use tool with well-structured navigation for building substation monitoring systems. The SMS 510 substation monitoring tool is the successor of the proven SMS 010 substation monitoring packages.…

    • 1394 Words
    • 6 Pages
    Powerful Essays
  • Good Essays

    POWERAPPS

    • 735 Words
    • 3 Pages

    The incomer transformer panel is equipped with a SEPAM 80 Series relay for integrated transformer protections…

    • 735 Words
    • 3 Pages
    Good Essays
  • Good Essays

    assign 1 magnetism

    • 1742 Words
    • 7 Pages

    By research and investigation describe the arrangements and features of an electrical supply system from generation through transmission and distribution to end users.…

    • 1742 Words
    • 7 Pages
    Good Essays
  • Good Essays

    Power System Stability

    • 2082 Words
    • 9 Pages

    Dept. of Electric Power Engineering, FEI TU of Košice, Slovak Republic Dept. of Electric Power Engineering, FEI TU of Košice, Slovak Republic 3 Dept. of Electric Power Engineering, FEI TU of Košice, Slovak Republic…

    • 2082 Words
    • 9 Pages
    Good Essays
  • Good Essays

    Power Station

    • 9162 Words
    • 37 Pages

    References: [1] V.K. Mehta & Rohit Mehta, “Principles of Power System,” Third Edition, S.Chand & Company Ltd., INDIA, 2003, pp.41-55…

    • 9162 Words
    • 37 Pages
    Good Essays
  • Satisfactory Essays

    Substation design

    • 1649 Words
    • 7 Pages

    “Design of 400/220kV Sub-station” S.M. MUJUMDAR 27th April 2005 Mumbai General Manager (sub-station Engineering) Jyoti Structures Ltd., Agenda  Overview of 400kV sub-station  Design Process  Design considerations  Question / Answer Imp. considerations in substation design      Safety of personnel and equipment Reliability and Security Adherence to  Statutory obligations – I.E. rules, Environmental aspects  Electrical design considerations  Structural design considerations Ease of maintenance Possibility to Expand System parameters Sr.…

    • 1649 Words
    • 7 Pages
    Satisfactory Essays

Related Topics